Jump to content
Sactown Plumbing Guide

Explainer ยท Sacramento

No hot water

No hot water almost always traces to the water heater: no power, no gas, a failed part, or a tank at the end of its life. Work through these checks in order, then decide whether to repair or replace.

A shower head with no hot water running and a hand on the lever

If you have no hot water, start with the heater's power or gas: check the breaker for an electric unit, or the pilot and gas control for a gas unit. Then check the thermostat setting and whether hot water is missing at every tap or only one. Most causes are simple parts. If the tank is old or leaking, replacement is the answer. For the full range of fixes, see water heater repair and replacement.

What is the first thing to check when there is no hot water?

Check whether the water heater has power or gas. For electric, look at the breaker and the reset button. For gas, look at the pilot light or ignition display. Then confirm the thermostat is set around 120 degrees and the cold inlet valve is fully open.

A quick sequence that takes ten minutes:

  1. Which taps? If only one tap has no hot water, the fault is at that fixture or its mixing valve, not the heater.
  2. Is the heater running? Listen and feel: a warm outlet pipe and a humming or burning sound suggest it is heating.
  3. Breaker. Electric heaters have a double-pole breaker on their own circuit. Flip it fully off, then on.
  4. Reset button. On an electric unit, remove the upper panel with the power off and press the red reset button.
  5. Pilot or ignition. On a gas unit, check the pilot is lit or the digital display shows no fault code.
  6. Valves. Confirm the cold inlet valve above the tank is open.

If you smell gas at any point, leave the house, call 911, then the PG&E gas emergency line. Do not try to light a pilot if you smell gas.

Why would I have no hot water on an electric water heater?

The usual causes are a tripped breaker or reset, a failed heating element or thermostat, or a wiring fault. Elements often last 6 to 10 years. When the upper element or thermostat fails, you get no hot water; when only the lower fails, you get a short supply that runs out fast.

Most electric repairs are small. Fixr's water heater repair guide lists $200 to $750 to replace a heating element and $100 to $250 for a thermostat, labor included. If the reset button trips again straight away, do not keep pressing it: the heater has a fault. Our guide to a 50 gallon electric water heater covers elements, repair kits and what to test. Working inside the panel means 240 volts, so switch the breaker off and test the wires first, or hire a local plumber or electrician.

Why would I have no hot water on a gas water heater?

The common causes are a pilot that has gone out, a worn thermocouple, a faulty gas control valve, a blocked burner or flue, or the gas supply being off. A pilot that will not stay lit usually points to the thermocouple, which is a small part that proves the flame to the gas valve.

Line drawing of a gas water heater's control valve, pilot flame and burner

Relighting a pilot is something manufacturers explain in the owner's manual and on the label on the heater, and many homeowners do it. If it goes out again within a day or two, stop: gas appliances are regulated, and further work, including replacing the gas control, belongs to a local plumber. A thermocouple replacement is a modest repair, which Fixr's water heater repair guide lists at $150 to $325. A new gas control costs more. If the burner flame is yellow or you see soot, turn the unit off and call for service. See A. O. Smith water heater repair if you have that brand.

If gas has been shut off to the whole house, for example after a utility visit, the heater needs a relight after service resumes.

What if there is hot water but it runs out quickly?

Hot water that runs out fast usually means a failed lower element on an electric unit, a dip tube that has broken and mixes cold water into the output, heavy sediment, or a tank that is too small for the household. Each has a different fix, and the cost ranges from low to a full replacement.

  • Sediment. Minerals take up space and insulate the heat. Flushing helps; see how to flush a water heater.
  • Dip tube. A plastic tube that sends cold water to the bottom. When it cracks, cold water shortcuts to the top.
  • Mixing valve or thermostat setting. Turning the thermostat down can seem like a failure.
  • Demand. A new teen in the house or a new tub can outgrow the tank.

If the household has outgrown a 40 gallon tank, read about sizing before you buy again: 40 gallon gas water heater sizing explains first hour rating.

When is no hot water a sign the heater is finished?

If the heater is past 10 to 12 years, the tank is leaking, there is rust-colored water, or repairs have started to repeat, replacement is usually the better choice. A leaking tank cannot be repaired. This Old House's water heater cost guide (updated June 2026) puts an installed tank water heater at $1,200 to $2,300.

For guidance on age, see how long a water heater lasts. Replacement involves the City of Sacramento's water heater permit, earthquake bracing, and, for most homes, a contractor with a CSLB license, since California requires one for jobs of $1,000 or more. See water heater replacement cost for ranges, or look at tankless and heat pump options in the tank versus tankless guide.

What if the house has no hot water and it is urgent?

Closing the cold inlet and turning off power and gas protects the house while you wait. Many local plumbers handle same-day calls, though evening and weekend visits usually cost more. See emergency water heater repair for what to expect. In the meantime, heating water on the stove covers washing and dishes.

A cold shower is uncomfortable but not dangerous in Sacramento's climate. The risk is leaks and gas, so treat those two as urgent and the rest as same-week. Browse other guides from the homepage.

Questions people ask

How long does it take to fix no hot water?

A reset, thermostat setting or relit pilot takes minutes. An element, thermostat or thermocouple repair is usually a one-visit job of one to two hours. A replacement takes half a day. Parts for older or unusual models can add a day or two.

How much does it cost to fix no hot water?

Fixr's water heater repair guide says repairs cost $150 to $750, with an average of $450, and a gas valve replacement is $150 to $300. A full replacement is $1,200 to $2,300 installed, per This Old House's water heater cost guide (updated June 2026). Sacramento prices vary, and the specialist quotes the real price after seeing the unit.

Why do I have no hot water in only one tap?

The tap's cartridge, mixing valve or a clogged aerator is the likely cause, not the heater. Check whether other taps run hot. If only a shower has the problem, the shower valve cartridge may need replacing.

What should I ask before I hire someone for no hot water?

Ask whether the visit fee goes toward the repair, what the diagnostic costs, and whether they will give both repair and replacement prices. Ask for the CSLB license number and check it online.

Do I need to be home for the repair?

Someone needs to give access to the heater, which is often in a garage, closet or attic. For a replacement, be reachable for the whole visit.

Sources used

Last changed