Jump to content
Sactown Plumbing Guide

Explainer ยท Sacramento

A. O. Smith water heater repair

A. O. Smith tank heaters fail in the same few ways as other brands: pilot or ignition faults, elements and thermostats, and tank leaks. This guide shows what to check, what to leave to a plumber, and what repairs cost.

A water heater in a garage with its lower access panel removed

A. O. Smith makes residential tank water heaters, tankless units and heat pump models, and a plumber can repair most of them with standard parts. Common faults are a pilot or igniter that will not stay on, a failed element or thermostat, a worn relief valve, and a tank that has started to leak. Fixr's water heater repair guide lists $150 to $750 for repairs, with an average of $450. A leaking tank means replacement. For the wider list, see water heater repair and replacement.

What do I need to know before repairing an A. O. Smith water heater?

Find the data plate first. It lists the model number, serial number, fuel type, capacity and test pressure, and it tells a plumber which parts fit. Then download the owner's manual for that model number from the manufacturer's website. The manual has a troubleshooting chart for your exact controls.

The data plate also shows the age. The serial number often encodes the production month and year, and the manual or the manufacturer's site explains how to read it. Age matters because the tank's warranty, commonly 6 to 12 years on residential tanks, may have ended, and parts-only coverage often does not pay for labor. Check your paperwork before you pay for a repair.

Make a note of the fuel type, as it decides what you may touch. Gas controls and venting are regulated work. Electric heaters carry 240 volts. Neither is a place to guess.

What are the most common A. O. Smith water heater faults?

The most common faults across gas models are a pilot that will not light or stay lit, a failing thermocouple or flame sensor, a faulty gas control, and sediment. Across electric models they are failed elements, thermostats and tripped reset buttons. On both types, the tank can corrode and leak.

Line drawing of the inside of a tank water heater showing its main parts
FaultTypical signTypical repair
Thermocouple or flame sensor wornPilot goes out, no hot waterReplace part, $150 to $325
Gas control valve failedNo ignition although the pilot is litReplace valve, $150 to $300
Element failed (electric)Warm water only or noneReplace element, $200 to $750
Thermostat failed (electric)Water too hot, too cold or noneReplace thermostat, $100 to $250
Relief valve drippingWater at the discharge pipeReplace valve, $100 to $250
Tank leakWater pooled at baseReplace water heater, $1,200 to $2,300

These figures come from Fixr's water heater repair guide (updated August 2025) and This Old House's water heater cost guide (updated June 2026). They vary with access, parts and brand, and a local plumber quotes the real price. Our guide to no hot water walks through the checks that sort the first four faults from each other.

How do I read the error or indicator on an A. O. Smith heater?

Many gas models have a gas control with an indicator light or digital display, and many electric and heat pump models have a status light or panel. The manual's chart translates the blink count or code into a likely cause. Match the code to your exact model, because codes differ between series.

If you find a code, write it down along with the model number before you call. A plumber can often arrive with the right part. Some codes point to a simple cause, such as a blocked intake or a tripped thermal cutoff, which may need a reset after the cause is fixed. If the same code returns after a reset, the fault has not been cleared.

For gas models with a flammable vapor ignition resistant design, a flame arrestor at the base of the unit can clog with lint and dust, which stops ignition. Vacuuming the screen with the heater off is a typical maintenance step in the manual. If you smell gas, leave, call 911 and then the PG&E gas emergency line, and do not operate the heater.

What can I check myself, and where does DIY stop?

You can check the breaker, reset button, thermostat setting, cold inlet valve, and the area around the heater for water. You can relight a standing pilot if the manual shows how and there is no gas smell. You should not replace gas controls, rework venting, or open a live electrical panel.

California regulates this work. A contractor with a CSLB license is required for jobs of $1,000 or more in labor and materials, and replacing a heater normally exceeds that. Water heater permits and fees are listed on the City of Sacramento's building pages. New and replacement heaters must be braced under Health and Safety Code section 19211, so a replacement should include straps.

A few safe checks:

  • Press the reset button on an electric heater with the power off, then restore power once.
  • Confirm the thermostat is near 120 degrees.
  • Flush a few gallons to clear sediment; see how to flush a water heater.
  • Look at the relief valve discharge pipe for drips.

When should I repair an A. O. Smith heater, and when should I replace it?

Repair if the unit is under about 8 years old and the fault is a part, such as an element, thermostat, thermocouple or valve. Replace if the tank leaks, the unit is past 10 to 12 years, or the repair is near half the price of a new heater. Ask the plumber to price both.

A newer unit may save energy, and the choice of type matters: tank versus tankless and the page on water heater replacement cost help you compare. If the relief valve is the problem, see pressure relief valve replacement. Browse other guides from the homepage.

Ask the plumber whether the old heater's warranty can be claimed. Some warranties need the original receipt, proof of professional installation or a registration, so check before you throw the paperwork away. A plumber can also tell you whether the part number is still made.

Questions people ask

How long does A. O. Smith water heater repair take?

Most part repairs take one to two hours on one visit, such as an element, thermostat, thermocouple or valve. If the plumber has to order a part for an older model, add a day or two. A replacement takes half a day.

Is an A. O. Smith water heater worth repairing?

It depends on age and fault. A part failure on a heater under 8 years old is usually worth fixing, while a tank leak never is. Past 10 to 12 years, a replacement often makes sense even for a small repair, because other parts are close behind.

What should I ask before I hire someone to repair an A. O. Smith heater?

Ask for the CSLB license number and check it online. Ask what the visit fee covers, whether it goes toward the repair, whether they use manufacturer parts, and whether the repair carries a warranty on parts and labor.

Do I need to be home for an A. O. Smith repair?

Someone needs to let the plumber reach the heater and approve the quote. The water and power or gas are off for part of the visit. Ask for a time window when you book.

Sources used

Last changed